What the counter does
Boards with a Q-Code display show a counting sequence during memory training. The sequence moves from 00 through 09 at roughly one-second intervals, then resets to 00 before the normal boot process continues.
In short, the sequence runs 00, 01, 02 and so on up to 09, then drops back to 00. It exists, as one report put it, to stop users from thinking the system has hung.
What the counter is not
This is an activity indicator, not a countdown or a progress bar.
- Reaching 09 does not mean training finishes in ten seconds. Training time still depends on the memory configuration, the CPU's memory controller and the BIOS settings.
- Dual-rank kits and high-capacity kits may need more time.
- A changing code is a good sign that the board is still working. It is not proof that the boot will succeed. A machine that never finishes startup still needs normal troubleshooting.
- The sequence tells you nothing about whether your memory is healthy.
Memory training is the step where the platform works out stable timings and settings for the installed RAM. It is usually longest on the first boot. It can run long with higher-capacity kits and aggressive memory settings. Before this change, a long training run could look the same as a hang. The diagnostic display often showed a static code.
One regional report claims the counter continues past 09 into hex values such as 0a and 0b. The ASUS-based reporting describes a reset to 00 instead, so I would treat that claim as unconfirmed.
Which boards are covered
ASUS's announcement lists beta BIOS versions for selected X870/X870E and X670E boards. The version numbers differ by model, even within one chipset family.
- X870/X870E examples: Crosshair X870E Hero (2603), ROG Strix X870E-E Gaming WiFi (2603), ROG Strix X870E-E Gaming WiFi7 Neo (1203), TUF Gaming X870E-Plus WiFi7 (2603) and ProArt X870E Creator WiFi (2603).
- X670E examples: Crosshair X670E Hero (4103), ROG Strix X670E-E Gaming WiFi (4103) and TUF Gaming X670E-Plus (4013).
That is a sample, not the full list. One outlet says B850 and B650 boards are also covered, but the ASUS list I could verify names only X870, X870E and X670E boards. Check your exact model on ASUS's support page and read the release notes before flashing.
Other vendors are following. According to a hardware leaker's post, MSI has also released AGESA 1.3.0.1f Patch A for select models, with the new memory-training post code. The same post says MSI's notes mention a Vcore limit of 1.4V for select Ryzen 8000 series CPUs. That is a secondhand claim, so check the notes for your own board.
Beta caveats
These are test releases, and I would not put one on a machine you rely on every day. Two points to keep in mind:
- ASUS warns against loading saved CMO profiles created under a different AGESA version. After updating, re-enter your settings and validate them.
- The behaviour may or may not change in the stable release.
You do not need new RAM or a new motherboard for the counter. It arrives through firmware on a board that already has a Q-Code display.
Practical advice
- If you are not troubleshooting anything, there is no urgent reason to flash a beta only for this.
- If you are building a new AM5 system with big DDR5 kits, the counter may spare you some anxiety. Give the board time before assuming a fault, especially on the first boot.
- If the count loops for a long time and nothing ever appears on screen, the counter is doing its job. It is telling you the board is still alive, not that all is well. At that point, reseat the memory, try a single module, or clear CMOS, as you normally would.
Bottom line
This is a modest quality-of-life change, but a welcome one. It makes a long, confusing step easier to read. It does not speed up memory training or improve stability, and no source I found claims either. It is a beta, so test it on a system where a rollback would not hurt.
References
- ASUS adds a tiny progress counter to make Ryzen RAM checks less unnerving - MIXED News MIXED News · 2026-11-18T20:16:00+00:00
- ASUS adds DDR5 memory-training counter with AMD AGESA 1.3.0.1f beta BIOS - VideoCardz.com videocardz.com
- AM5 Debug Displays Now Count From 00 To 09 During DDR5 Memory Training With AMD's AGESA 1.3.0.1f Patch A, Ending The Apparent Boot Hang wccftech.com