A laptop displays Windows Disk Management formatting a 2 TB drive beside an NVMe SSD, with a graphic comparing storage speeds.
MakeUseOf's Yasir Mahmood says he dropped USB flash drives for NVMe SSDs in external enclosures, and for big transfers the idea holds up. The catch is that the speeds quoted on the SSD box and the speeds you get through a cheap enclosure are very different numbers. This guide covers where the gains come from, what to check before buying, and how to wipe and format an old boot drive in Windows without wiping the wrong disk.

A laptop displays Windows Disk Management formatting a 2 TB drive beside an NVMe SSD, with a graphic comparing storage speeds. The pitch: why flash drives struggle with big copies​

Mahmood's complaint is familiar to anyone who has moved a 4K video project, a game backup or a photo library. A flash drive is fine for documents, but sustained writes of 50 GB or more expose its limits. His account is that write speeds sag as the drive fills and heat builds in a tiny body.

His fix is an M.2 NVMe SSD in a USB-C enclosure. He says setup is simple, with no extra drivers needed on Windows, macOS or Linux. He also says it works well with an old boot drive pulled from a laptop or PC after an upgrade.

These are his personal observations. The article gives no named flash drive, no test method and no measured results. Treat his "15–30 times faster" figure as one writer's impression, not a benchmark.

The correction that matters: the link sets the speed​

An NVMe drive's rated speed is not the speed of the finished external drive. The enclosure's bridge chip, the port on your PC, the cable and the SSD itself all limit the result.

Mahmood suggests a PCIe 4.0 drive reaching about 7,000 MB/s read, and says Thunderbolt 4 gets "close to that." That overstates it. Thunderbolt 4 guarantees a 40 Gbps link, which is a signaling rate. The theoretical ceiling is about 5 GB/s before protocol overhead, and real copies land lower.

Reports gathered for this piece put realistic figures in tiers:

  • 10 Gbps (USB 3.2 Gen 2): real-world numbers for this tier land around 900 to 1,050 MB/s. A fast Gen 4 drive can pass 7,000 MB/s inside a desktop, and a 10Gbps case caps it near 1,000 MB/s in sequential transfers.
  • 40 Gbps (USB4 or Thunderbolt): Per CMRCheck's interface comparison, USB4 40Gbps drives typically hit 3,000–4,500 MB/s in real-world use, while Thunderbolt 3/4 drives typically land at 2,000–2,800 MB/s. Treat those as secondary-source ranges, not guarantees.
  • Faster than that: Intel says nothing about drives here, but it does specify that Thunderbolt 5 offers up to 80 Gbps bidirectional bandwidth, double the previous generation. A drive still can't use all of it.

Even the 10 Gbps tier is a big step up from a typical flash drive. The point is that a $100 PCIe 4.0 SSD in a $30 enclosure won't behave like one in a $100 USB4 enclosure.

USB4 and USB-C labels can mislead​

The USB Implementers Forum says USB4 connections scale to the best mutual capability of the devices involved. That includes older USB 3.2 and Thunderbolt 3 hosts. It also says 80 Gbps operation needs 80 Gbps certified cables.

A USB-C connector can carry anything from 5 Gbps to Thunderbolt speeds. Industry buying guides make the same point. Connecting a 40Gbps enclosure to a 10Gbps USB port will generally make it operate at the lower supported speed. One reviewer put it bluntly: A 40Gbps box on a 10Gbps port is a 10Gbps box that cost twice as much.

Intel's Thunderbolt page says you can spot Thunderbolt ports by the lightning-bolt icon beside the USB-C port, or by checking your PC's I/O specification. It also says Thunderbolt 5 on Windows needs Windows 11 version 23H2 or later.

Buying checklist​

  1. Know your port. Find out whether your PC's USB-C port is 10 Gbps, 20 Gbps, USB4 or Thunderbolt. Don't buy more enclosure than the port can use.
  2. Match the enclosure to the drive's protocol. It must support NVMe, not just an M.2-shaped SATA drive. A SATA M.2 drive is capped by SATA itself, so a fast enclosure can't help it. Also check the length (2230, 2242, 2260 or 2280) and the maximum capacity.
  3. Use the right cable. Using an uncertified or under-specced cable is one of the most common causes of underperforming external NVMe setups.
  4. Think about heat. Look for an aluminum body and a thermal pad. A StarTech quick-start guide for a USB4 enclosure warns that M.2 drives can get hot in prolonged transfers. Mahmood says a warm case means the heatsink is working, which is reasonable. But warmth alone doesn't prove the drive is running well, and heavy throttling is a real risk with fast drives in sealed cases.
  5. Match the drive to the enclosure. One reviewer notes that a 10Gbps enclosure cannot use a fast PCIe 4.0 drive, so a modest, cool-running PCIe 3.0 model is the sensible match and saves money. A good old drive pulled from a laptop may be all you need.

The prices in the original article ($70–$110 for a 1 TB PCIe 4.0 SSD, $30–$70 for an enclosure) are unsourced and drift quickly, so check current listings. The UGREEN enclosure in the article's product box is listed as 10 Gbps USB 3.2 Gen 2, for M and B+M key drives in 2230 to 2280 sizes up to 8 TB, with no SATA or mSATA support. Those are listing claims for one product, not universal enclosure properties.

Tom's Hardware ran its own tests in July 2026 of old drives reused as external storage, in enclosures of up to 80 Gbps. Its page text available here is too brief to quote results. Its premise supports reusing old drives, but it doesn't validate any particular speed multiplier.

Repurposing an old Windows boot drive​

This procedure erases data. Back up anything you want to keep first.

What you'll need​

  • The NVMe SSD installed in its enclosure and connected to your PC.
  • An account in the Administrators or Backup Operators group. Microsoft lists this as a prerequisite for disk setup.

Steps​

  1. Connect the enclosure.
  2. Press Windows key + X and choose Disk Management. Microsoft says you can also open it by searching for "Create and format hard disk partitions" and running it as administrator. If that fails, open Computer Management, then Storage, then Disk Management.
  3. Identify the right disk. A drive that held Windows will show several partitions. Compare the capacity with the drive you installed, and don't touch your internal system disk.
  4. Right-click each partition on that disk and choose Delete Volume. Microsoft notes that EFI System Partition and Recovery Partition entries are normally left alone on a working PC. On a different disk you've confirmed you're wiping, they can go too. The drive may refuse to delete some protected partitions from the Disk Management menu.
  5. When the space shows as Unallocated, right-click it and choose New Simple Volume, then Next.
  6. Accept the default size to use the whole drive, assign a drive letter, and choose a file system. Microsoft says this is usually NTFS.
  7. Select Finish.

If the disk shows as Offline, Microsoft says to right-click it and choose Online. If it's Not Initialized, you'll be asked to initialize it. Microsoft says the default partition style is GPT, which most PCs use for SSDs and which supports volumes over 2 TB. MBR is the older style.

What success looks like​

The new volume shows as Healthy in Disk Management and appears in File Explorer with its drive letter.

If something goes wrong​

Microsoft's Disk Management troubleshooting guidance suggests:

  • Right-click the disk and select Online if it's offline.
  • If the drive is unplugged, plug it back in, then choose Action, then Rescan Disks.
  • Try a different cable, since Microsoft notes cables fail often.
  • Check Device Manager for devices with an exclamation mark.
  • Plug the drive into another PC. If it fails there too, the disk is probably the problem.

Microsoft also warns not to create a new volume or format a disk if you're trying to recover files from it.

Cross-platform caveat​

Mahmood says these setups work across Windows, macOS and Linux. That is true for the hardware connection. A drive formatted NTFS is natural on Windows, but write support on other systems depends on the OS and configuration. If you move between platforms, check your file system choice before you commit terabytes to it. I didn't find a primary source for detailed macOS or Linux behavior, so I'm not making claims there.

Do you need to format at all?​

Not always. Formatting gives you a clean single volume with the full capacity. Mahmood notes that keeping the drive as a bootable backup is also possible, at the cost of space lost to Windows and recovery partitions. If the old drive still holds files you want, copy them off before you delete anything.

Flash drives aren't dead​

Mahmood admits flash drives still make sense for quick document transfers, small toolkits and anything that needs to fit on a keychain. An NVMe enclosure is bulkier and costs more. His claims that cheaper flash drives often lack SMART monitoring, error correction or write endurance are plausible but unsupported by product-level evidence, so don't take them as universal facts.

Bottom line​

  • If you regularly move tens of gigabytes, a properly matched NVMe enclosure can be a big upgrade over a flash drive.
  • The speed you get depends on the weakest link: port, cable, enclosure chip and drive.
  • A 10 Gbps setup commonly lands near 1 GB/s. USB4 or Thunderbolt setups can go several times higher, depending on the host.
  • Reusing an old drive is a cheap way to try this, but only after you've backed up, confirmed the correct disk in Disk Management, and accepted that deleting volumes erases the data.
 

References

  1. I stopped using USB flash drives for transfers because this is so much faster MakeUseOf 2026-11-20T14:00:16+00:00
  2. Testing old drives as external storage to avoid price hikes — hard drive, SATA SSD, and NVMe in enclosures up to 80 Gbps, tested | Tom's Hardware tomshardware.com
  3. An external NVMe in a USB4 enclosure became the best drive I own xda-developers.com