Who this applies to
Nvidia's updater page lists four supported models, all with G-Sync Pulsar:
- Acer Predator XB273U F5
- AOC AGON PRO AG276QSG2
- ASUS ROG STRIX Pulsar XG27AQNGV
- MSI MPG 272QR X36 (see the naming note below)
These are all 1440p, 360Hz panels. Pulsar combines variable refresh rate with timed backlight strobing, which cuts perceived motion blur without giving up tear-free play.
MSI naming wrinkle. The updater's live list says "MPG 272QR X36". Nvidia's support article, along with coverage from Guru3D, Club386 and TweakTown, says "MPG 272QRF X36". Check the exact model printed on your monitor and compare it against the updater's list before you start.
Version-number wrinkle. Nvidia's support page is headed "Firmware Version 1.1.6" and its intro text still mentions 1.1.6. Its changelog opens with 1.1.10, though. VideoCardz reports that Nvidia has released firmware 1.1.10 for its current 1440p 360Hz monitor lineup, with the changes previewed in August. The heading looks like a stale title. The updater itself checks your connected monitor and lets you pick versions, including rolling back to an earlier one.
What 1.1.10 changes
These are Nvidia's own claims, not independent measurements:
- Pulsar stays active longer. It turns itself off less often in what Nvidia calls "high entropy" games, meaning visually busy ones.
- Moving-image sharpness improves at 240Hz and 360Hz, for both ULMB2 and Pulsar.
- The sharpness of ULMB 60 now carries over to 240Hz and 360Hz ULMB at the full 480 nits of brightness.
Nvidia says its measurements used an iBoson VisMotion-M pursuit camera. The figures in its table:
| Refresh rate | ULMB2 pulse width | Brightness | FW 1.1.8 MPRT | New firmware MPRT |
|---|---|---|---|---|
| 240Hz | 100 | 480 nits | 2.05 ms | 1.37 ms |
| 240Hz | 50 | 240 nits | not listed | 0.97 ms |
| 240Hz | 25 | 120 nits | not listed | 0.83 ms |
| 360Hz | 100 | 480 nits | 1.64 ms | 1.14 ms |
The "1,000Hz equivalent" label refers to motion clarity, meaning how much blur your eye perceives. Guru3D notes it does not mean the monitor accepts a 1,000Hz signal. The best number also comes with a trade-off. The 0.97 ms result is at a pulse width of 50 and 240 nits, which is dimmer than the 480-nit rows.
Should you bother?
Earlier releases also fixed real problems. Version 1.1.8 added a pulse-width slider on MSI and AOC models, reduced input lag at 240Hz, and added a workaround for G-Sync disappearing after monitor sleep. Nvidia admitted that workaround did not cover every case. Version 1.1.6 corrected the EDID white point to D65 and fixed input auto-switching bugs.
Two caveats from the community and press:
- Club386 notes the update does not fix the 320fps bug that causes high input lag. It also says connecting a secondary monitor seems to prevent that issue from appearing. Treat that as a reported workaround, not an official fix.
- One forum user said an MSI monitor's on-screen display still showed the old "FW.045" label after the update, while the updater confirmed 1.1.10. If your menu seems unchanged, re-check the version in the updater itself.
If your monitor is behaving, the update is optional. If you play fast competitive shooters, or you've seen Pulsar drop out in busy scenes, it is more tempting.
What you need
- A Pulsar monitor from the supported list.
- A Micro-B USB data cable running from the monitor's firmware update port to your computer. Nvidia says the cable that came with the monitor will work. HDMI, DisplayPort and charge-only USB cables won't.
- A supported browser: Chrome 61 or newer, Edge 79 or newer, or Opera 48 or newer.
- A supported operating system: Windows, macOS, Linux, Android or ChromeOS. iOS is not supported.
- Stable power. A laptop on battery or a flaky power strip is a bad idea here.
Step-by-step update
- Open Nvidia's G-Sync Pulsar firmware updater in a supported browser. Choose Update Monitor, then Check version and update. Accept the license terms and pick your monitor's manufacturer.
- Connect the Micro-B cable between the monitor's update port and your PC.
- With the monitor powered on, use its buttons or joystick to open the on-screen menu and enable Firmware Update Mode. The exact menu path differs by manufacturer. The updater shows brand-specific instructions.
- Check for success. The status light should flash slowly, and the screen should show "Firmware Update Mode" in its top-left corner.
- Back in the browser, select the monitor in the device prompt and allow the connection. The listed name may include the manufacturer and model, or just "NVIDIA G-SYNC".
- Let the tool read your firmware version, choose the one you want and install it.
- Wait for the completion message. The monitor restarts. Only then should you unplug the USB cable and close the tab.
Nvidia says updates typically take 5 to 10 minutes. The tool's own step labels suggest the download and install stages can each run five minutes or longer, so don't treat 10 minutes as a promise.
If something goes wrong
Monitor isn't detected. First confirm Firmware Update Mode is actually active, with the light flashing slowly and the on-screen text visible. Then suspect the cable. Nvidia's advice is to make sure it carries data, reconnect it or try another.
The update fails or is interrupted. Nvidia says the tool will alert you and, in most cases, let you retry safely.
The monitor won't start. Nvidia describes a Recovery Mode:
- Unplug the monitor's power.
- Wait 15 seconds.
- Hold any monitor button, or push the joystick in any direction.
- Reconnect power while still holding the button, and keep holding for 10 seconds.
- Look for the slowly flashing status light, then reopen the updater and follow its "My monitor won't start up" steps.
You can skip those steps if the light is already flashing slowly.
The risk
Don't interrupt the flash. Nvidia warns that unplugging cables, losing power, crashing the system or closing the tab mid-install can leave the monitor malfunctioning, with its terms going as far as permanent loss of function. Don't touch the cables, don't let the PC sleep, and don't close the tab.
Nvidia says using its official tool doesn't by itself change your monitor warranty. It also points out that the warranty comes from the monitor's maker or seller, so check their terms if that worries you.
Bottom line
The method looks silly, but a browser-based flasher with no app to install is arguably tidy. The Micro-B cable is the real obstacle, because most people no longer have one in a drawer. Check your exact model, find a data-capable cable, plug in a stable power source and keep your hands off it until the tool says it's done.
References
- Your Nvidia G-Sync monitor might need to be updated in the silliest way possible How-To Geek · 2026-11-17T16:30:15+00:00
- G-SYNC Pulsar Firmware Version 1.1.6 update | NVIDIA nvidia.custhelp.com
- NVIDIA G-SYNC Pulsar firmware 1.1.10 improves 240/360Hz motion clarity, delivers sub-1ms MPRT - VideoCardz.com videocardz.com