Behind the internet-ready absurdity, however, sits a surprisingly serious piece of hardware engineering for Windows enthusiasts, custom liquid-cooling builders, and homelab administrators. If you have ever wondered where motherboard fan headers stop, where power rails start melting, and what separates "100 fans wired together" from "100 individually controlled fans," Karanovic's wind wall offers a vivid—and refreshingly honest—masterclass.
Anatomy of a 100-Fan Wall: Channels vs. Raw Fan Count
Building a 10-by-10 grid of spinning Noctua blades is an exercise in hardware logistics as much as electronics. According to Tom's Hardware and Hackaday, Karanovic secured the 100 fans through what he described as "a ton of luck and a good friend," then mounted the entire array onto an aluminum-extrusion frame using custom 3D-printed brackets to wrangle both the housings and the sprawling cable harness. All told, the assembly swallowed 200 fan grills, 800 screws, and dozens of PWM fan splitters.
Here is the critical engineering distinction every PC builder needs to catch before eyeing a giant splitter tree: OpenFAN XL has 10 output headers, not 100.
- The 10×10 Grid Setup: In the primary configuration, Karanovic wired one row of 10 fans to each of the controller's 10 channels. That means the 100 fans were not individually addressable; every fan sharing a header received the same control signal, making a 10-fan bank the smallest independently tunable unit.
- The 50×2 Stress Test: To prove the board could shoulder heavier per-channel loads, Karanovic reconfigured the splitters so that just two headers drove 50 fans apiece.
- Where the Ceiling Sits: Karanovic reported that running 100 fans was "no sweat" for the OpenFAN XL, estimating its practical limit at roughly 200 fans in its current revision. While multiplying 50 fans across all 10 headers might tempt back-of-the-napkin math up to 500 spinners, other hardware and power constraints keep the realistic ceiling closer to 200.
As a hardware reality check, it also matters which fans are on the end of those splitters. As commenters on Hackaday noted, quiet Noctua PC fans typically sip only around a watt or two each, whereas heavy-duty 12V server blowers can demand upwards of 20 to 30 watts apiece. One working configuration with 100 Noctua units proves this specific test ran smoothly—it is not a blanket guarantee that any arbitrary 100 high-static-pressure server fans can be chained onto a single controller without respecting current limits.
Section Takeaway: Using PWM splitters lets a 10-channel controller spin 100 fans in synchronized banks, but channel count still dictates control granularity—and total amperage always sets the hard ceiling.
Under the Hood: What OpenFAN XL Brings to PCs and Servers
Strip away the YouTube theatrics, and Karanovic Research's preliminary specifications published on its project forum explain why OpenFAN XL exists alongside the standard OpenFAN Controller. Standard motherboard headers typically top out around 1A to 2A, and the original OpenFAN relied on SATA power—a connector whose 12V wiring standardly caps safe delivery around 54 watts (4.5A). That works fine for everyday desktop case fans, but it quickly hits a wall with high-current server fans or PWM liquid-cooling pumps.
OpenFAN XL targets those hungrier builds directly:
| Feature / Specification | Original OpenFAN Controller | OpenFAN XL (Preliminary Specs) |
|---|---|---|
| Fan / Pump Headers | 10 channels (standard PC fans) | 10 headers for fans or PWM water pumps |
| Max Current per Header | Standard desktop fan loads | Up to 3A per connector |
| Power Input Options | SATA power | PCIe, SATA, or USB-C PD (up to 10A total via PCIe) |
| Temperature Sensing | Relies on host/API telemetry or optional I2C/1-Wire | 4 dedicated NTC probe headers + onboard SHTC3 temp/humidity sensor |
| Offline / Stand-Alone Mode | Host PC USB required for software/network control | Non-volatile memory stores fan curves for autonomous offline operation |
| Expansion & Alerts | Unpopulated I2C / 1-Wire header | Expansion header (I2C, SPI, 1-Wire, GPIO, Alert pin) + Piezo/buzzer header |
The jump to PCIe power (delivering up to 10A total across all fans) and 3A per header is the real headline upgrade for workstation and custom-loop builders. Meanwhile, adding four dedicated NTC thermistor headers—though available reporting does not confirm whether external probes actively governed the 100-fan wall during the video—alongside an onboard SHTC3 temperature-and-humidity sensor and a buzzer alert header turns the board from a simple USB hub into a self-monitoring thermal appliance.
Section Takeaway: OpenFAN XL separates itself from basic fan hubs by pairing 3A-per-channel capacity and 10A PCIe power input with onboard environmental sensing and programmable offline autonomy.
Windows Integration, Stand-Alone Mode, and Open-Source Roots
For Windows users tired of bloated RGB-and-fan suites that hijack background CPU cycles just to spin three radiator fans, the software side of the OpenFAN ecosystem is arguably as compelling as the PCB.
Because OpenFAN XL is designed to be backwards-compatible with the existing OpenFAN software and open-source API, it inherits cross-platform support across Windows, Linux, and macOS (with Docker and Unraid integrations already established for the standard model). More importantly for desktop tweakers, the OpenFAN project integrates natively with FanControl on Windows via the FanControl.OpenFAN plugin. That allows Windows builders to map external coolant loop sensors or chassis fans directly against GPU hotspot, CPU package, or mixed sensor curves inside one lightweight interface.
Just as useful for homelabbers is OpenFAN XL's new stand-alone mode. By storing custom fan and pump curves in onboard non-volatile memory and reading its own NTC probes, the controller can manage cooling completely offline without a USB host attached—ideal for network switches, NAS enclosures, or dedicated server racks where plugging in a Windows PC isn't practical. Hackaday also notes that Karanovic plans to open-source the OpenFAN XL design once development wraps up, following the GPL-3.0 open-hardware and firmware precedent set by the original OpenFAN GitHub repository.
Section Takeaway: Windows users gain clean FanControl integration and an open API, while server and rack builders get hardware-stored fan curves that keep spinning even when no OS is connected.
Practical Reality Check—and That Wild Price Discrepancy
Karanovic himself freely admitted that a wall of 100 PC fans "probably makes no sense" as an everyday cooling tool. That hasn't stopped the tech community from daydreaming: Tom's Hardware suggested aiming the gust at a GPU or laptop for TrashBench-style cooling antics, while Hackaday readers pitched everything from a desktop wind tunnel and an oversized soldering fume extractor to a bedroom window cooler. In reality, industrial wind walls—like Caltech's 1,296-fan drone testing array—exist for specialized aerodynamics research, whereas desktop users are far better served by fewer, well-ducted fans matched to their static pressure needs.
Before anyone rushes to check out, however, there is a glaring price discrepancy worth flagging. Tom's Hardware listed the OpenFAN XL pre-order at $2,355 (discounted from $2,926)—a jaw-dropping figure that makes no sense for a single-board fan controller. Checking Karanovic Research's official web shop tells a very different story: the OpenFAN XL pre-order is listed in USD at $70.00, representing a 20% discount off its $87.00 regular price, with an estimated shipping window of January–February 2027. (The shop also notes that U.S. buyers face a posted +30% import tariff surcharge included at checkout.)
Whether you ever need to command 100 Noctua fans at once—spoiler: you almost certainly don't—Karanovic's stunt lands its point cleanly. Keep an eye on header amperage, respect the difference between SATA and PCIe power rails, and verify your currency settings before clicking "pre-order."
Section Takeaway: Treat the 100-fan wall as an entertaining proof-of-concept rather than a practical cooling blueprint, and rely on Karanovic Research's $70 USD pre-order listing rather than the four-figure pricing cited in initial coverage.
References
- Maker builds Mad Max-inspired wall of 100 Noctua PC fans Tom's Hardware · 2026-11-22T16:00:46+00:00
- One Hundred Gratuitous Case Fans? We’re Fans Of This. | Hackaday hackaday.com
- sasakaranovic.com forum.sasakaranovic.com