First, work out what "not working" means
"Connected" and "online" are different states. Windows decides a connection is limited by sending a small HTTP request to an internet server. If nothing comes back, you get the No Internet icon, even though your PC may be talking happily to the router. Microsoft also says a normal Wi-Fi icon doesn't guarantee everything works. A problem with a single app or website, or a firewall, can still block access.
That gives you three broad cases:
- Wi-Fi is missing or no networks appear. This is usually the adapter, a switch or a driver.
- Connected, but no internet. This is usually IP, DNS, proxy or router/ISP.
- Connected, but dropping or slow. This is usually signal, interference or power management.
Step 1: Run the built-in troubleshooter
On Windows 11, Microsoft says to start with the automated Network and Internet troubleshooter in the Get Help app. It runs diagnostics and tries to fix common problems. On older Windows or other devices, Microsoft points to the Network troubleshooter in Settings. That route is Start > Settings > Network and Internet > Status, then Network troubleshooter.
Step 2: Check the basics
- Open the taskbar's Network, Sound or Battery icons and confirm Wi-Fi is on and your network shows Connected.
- Go to Settings > Network & Internet > Airplane mode and make sure it is off.
- If your laptop has a physical wireless switch, check it. Not all devices have one.
Step 3: Forget the network and rejoin
In Settings, go to Network & internet > Wi-Fi > Manage known networks. Select your network, click Forget, then reconnect and enter the password. This clears a stale or corrupted saved profile. It's also a good moment to confirm you're typing the right password for the right network.
Step 4: Power-cycle the modem and router
Microsoft's procedure is more careful than "turn it off and on":
- Unplug the router, then the modem.
- Some modems have a backup battery. If the lights stay on after unplugging, remove the battery.
- Wait at least 30 seconds.
- Plug in the modem first and let its lights stop blinking. Then plug in the router and wait a few minutes.
Everyone on your Wi-Fi will be disconnected while you do this, so warn the household first.
Step 5: Try the other band and another device
Many consumer routers broadcast separate 2.4 GHz and 5 GHz networks. If you see both in the list, try the one you aren't using. Not every router or adapter supports both bands. Next, try the same network on a phone or another laptop. If that device connects, Microsoft says the fault likely lies with your PC rather than the router. Moving closer to the router is a cheap way to rule out signal strength.
Step 6: Reset the network stack with commands
Open Command Prompt as administrator and run these in order, testing afterward:
netsh winsock reset
netsh int ip reset
ipconfig /release
ipconfig /renew
ipconfig /flushdns
Microsoft describes these as resetting the TCP/IP stack, releasing and renewing the IP address, and flushing the DNS resolver cache. Hans India adds a restart afterward. Microsoft's command step says to check whether the connection is fixed, and its broader guide lists a restart as a separate step. A reboot is a sensible habit after the Winsock and IP resets in any case.
Step 7: Firewall, drivers and the adapter
Hans India suggests temporarily disabling third-party firewall software to see whether it blocks the connection. Microsoft's guidance does mention a firewall as a possible cause. Re-enable the firewall as soon as you've tested.
For the driver, Microsoft's procedure is more specific than "update or reinstall":
- Download the latest network adapter driver from your PC maker first. If the PC is offline, use another PC and a USB flash drive.
- Open Device Manager, expand Network adapters and find your adapter.
- Choose Uninstall device and tick "Attempt to remove the driver for this device".
- Restart. Windows should look for and install a driver. If it doesn't, install the one you saved.
Microsoft suggests this especially if Wi-Fi broke after a recent update.
If Wi-Fi is missing entirely
- Check the physical switch and the Wi-Fi toggle in Settings.
- In Device Manager, right-click the adapter and choose Enable device.
- Press Win + R, type
services.msc, find WLAN AutoConfig and choose Restart. - If the adapter isn't listed at all, Windows doesn't detect it. Check the manufacturer's website for a driver that works in Windows.
If the adapter is present but no networks appear
Microsoft lists two less obvious causes. The adapter may not support the band your router broadcasts, such as a 2.4 GHz-only adapter facing a 5 GHz network. Less commonly, the driver may filter the band out. In the adapter's Properties > Advanced tab, look for a Wireless Mode or Band setting and confirm it allows your network's frequency.
Step 8: Fix the "No Internet" and "keeps dropping" cases
Connected but no internet
- Toggle Wi-Fi off and on, then reconnect.
- Renew the IP with
ipconfig /releaseandipconfig /renew, and flush DNS withipconfig /flushdns. - Go to Settings > Network & Internet > Proxy and turn off any manual proxy settings.
- Check your IP address. An address starting 169.254 means Windows couldn't get one from the router. If you're not using static addresses, check that DHCP is enabled on the router.
- If you have a valid IP but can't ping your DNS server, Microsoft says you can try a different DNS server.
Separate the router from the ISP
Run ipconfig and find the Default gateway for your Wi-Fi network, then run ping followed by that address. Replies mean the PC reaches the router, so the trouble may be the modem or ISP. Check for an outage. No replies means you should try Ethernet straight to the modem. If that works, the Wi-Fi router is the culprit, and Microsoft recommends checking its firmware.
Frequent disconnections
Hans India recommends setting the adapter's power mode to Maximum Performance. Microsoft gives that same fix, but through a different route: Control Panel > Hardware and Sound > Power Options, then your plan's advanced settings. Under Wireless Adapter Settings, set Power Saving Mode to Maximum Performance. Microsoft separately describes a Device Manager route: open the adapter's Properties, go to Power Management, and untick Allow the computer to turn off this device to save power. Microsoft also suggests changing the router's wireless channel to reduce interference. The two power settings are different controls, so don't assume one replaces the other. On a laptop, either one can cost some battery life.
Authentication errors
If you get "incorrect password" errors despite entering the right one, Microsoft's list is: verify the password matches the router configuration, reboot the router, and update its firmware. It also mentions restoring the router to factory settings. That last step will wipe your router configuration, so treat it as a last resort rather than a quick fix.
When the basics fail: get evidence
Open an administrator Command Prompt and run:
netsh wlan show wlanreport
Microsoft says this creates an HTML report covering the last three days of Wi-Fi events, grouped by connection session. It also lists your network adapters, including any hidden ones, with driver version, driver date and a Problem number if the adapter has an error. A red circle in the summary chart marks an error. The report also records disconnect reasons and the results of several network scripts, which helps if a pattern emerges, such as drops at a particular time.
The last resorts
Microsoft's guide also lists Windows Update, a restart, and finally Network reset. Microsoft says Network reset should be the last step. On Windows 11 it's under Advanced network settings > Network reset; on Windows 10 it's Status > Network reset. It removes and reinstalls your network adapters and returns their settings to defaults. Afterward you may need to reinstall VPN clients or Hyper-V virtual switches. Known networks may also revert to a public profile, which makes your PC less discoverable.
A sensible order
- Read the icon, and run the troubleshooter.
- Check Wi-Fi, Airplane mode and any hardware switch.
- Test another device and the other band.
- Forget and rejoin the network.
- Power-cycle the modem and router.
- Run the command sequence and restart.
- Ping the gateway to separate PC, router and ISP.
- Reinstall the driver, using a saved manufacturer driver as a backup.
- Use Network reset last.
Verdict
The Hans India list is a fair checklist, but it's compressed. Microsoft's documentation supplies the missing parts: a driver backup plan, the 169.254 clue, the gateway ping that splits "my PC" from "my ISP", and the wireless report for stubborn cases. None of these fixes is guaranteed for every setup, and hardware or router faults can sit behind any of these symptoms. Work through them in order, though, and you'll usually find the cause before the nuclear option.
References
- Windows Wi-Fi Not Working? 8 Fixes to Get Back Online The Hans India · 2026-11-18T01:40:11+00:00
- Fix Wi-Fi connection issues in Windows | Microsoft Support support.microsoft.com
- Fix Wi-Fi connection issues in Windows | Microsoft Support support.microsoft.com