conceptualclarity
Senior Member
- Joined
- Jul 3, 2014
- Messages
- 30
*******************************************************************************
* *
* Bugcheck Analysis *
* *
*******************************************************************************
Use !analyze -v to get detailed debugging information.
BugCheck 1000007F, {8, 80042000, 0, 0}
*** WARNING: Unable to verify timestamp for VVBackd5.sys
*** ERROR: Module load completed but symbols could not be loaded for VVBackd5.sys
*** WARNING: Unable to verify timestamp for ambakdrv.sys
*** ERROR: Module load completed but symbols could...
A problem has been detected...
If this is the first time...
Check for viruses on your computer. remove any newly installed hard drives or hard drive controllers. Check your hard drive to make sure it is properly configured and terminated. Run CHKDSK /F to check for hard drive corruption, and then restart your computer.
*** STOP: 0X0000007B (0XF78A2528, 0XC000000E, 0X00000000, 0X00000000)
I had gone a good while without any blue screens, from Sept.21, till tonight. I was having CPU Usage dominated by System Idle Process, having my key programs be sluggish or unresponsive, so I shut my programs down one by one and clicked on Restart. I left the computer briefly as it was shutting down. I found it stuck on a blue screen when I returned.
The usual paragraph after the codes was missing.
I shut down the computer. I went into Safe Mode, and very quickly it landed on the same blue screen. I turned it off for a while. Then I tried to boot normally. I got a message screen (not the normal one from tapping F8) offering me options. I chose Last Known Good Configuration or whatever. The computer booted normally. At some point it turned into another sluggish session leading me to shut it down for twenty minutes. Since then it has been functioning well.
I brought up BlueScreeView and didn't see these two blue screens. I went to C:\WINDOWS\Minidump and saw that their logs were indeed absent.
I did enter CHKDSK /F at the command line. It told me that I'd have to reboot to do that. When I rebooted, the system chkdsked C rather than my external drive F. The C chkdsk found no problems: I watched it the whole time.
Anything I can do to ensure there won't be more failure to log blue screens? What does this one signify?
To be honest you need to obtain a disk either XP SP3 or upgrade to something later if the machine will allow. If you intend to keep XP running (which I don't advise) then you at least need to be armed with a disk to make good any errors.
You may well be fine for a while now you've gone back to an earlier time when the os was running smoothly. Use this time to get yourself a disk and then at least you'll have some control.
As mentioned probably Ebay is your best bet for XP but do be careful on what you purchase.
As long as the disk isn't corrupted and it is actually a windows install disk then you can at least re-install and then upgrade to the latest service pack ( SP3). It's just when I asked you to perform a System File Scan you said the machine asked for XP SP3 as it needed files off the disk to run. You never said whether you tried your disk or not?You believe my Dell XP reinstallation disk for XP Home with Service Pack 1a is not likely to be of much use?
This was probably caused by the following module: vvbackd5.sys (VVBackd5+0xCAFC)
Bugcheck code: 0x1000007F (0x8, 0xFFFFFFFF80042000, 0x0, 0x0)
Error: UNEXPECTED_KERNEL_MODE_TRAP_M
file path: C:\WINDOWS\system32\drivers\vvbackd5.sys
Bug check description: This indicates that a trap was generated by the Intel CPU and the kernel failed to catch this trap.
This appears to be a typical software driver bug and is not likely to be caused by a hardware problem. This problem might be caused by a thermal issue.
A third party driver was identified as the probable root cause of this system error. It is suggested you look for an update for the following driver: vvbackd5.sys .
On Thu 11/27/2014 8:42:23 AM GMT your computer crashed
crash dump file: C:\WINDOWS\Minidump\Mini112714-01.dmp
This was probably caused by the following module: ntoskrnl.exe (nt+0x5C85E)
Bugcheck code: 0x50 (0xFFFFFFFFF99814D6, 0x0, 0xFFFFFFFFBF968F6D, 0x0)
Error: PAGE_FAULT_IN_NONPAGED_AREA
file path: C:\WINDOWS\system32\ntoskrnl.exe
product: Microsoft® Windows® Operating System
company: Microsoft Corporation
description: NT Kernel & System
Bug check description: This indicates that invalid system memory has been referenced.
This appears to be a typical software driver bug and is not likely to be caused by a hardware problem.
The crash took place in the Windows kernel. Possibly this problem is caused by another driver that cannot be identified at this time.
On Thu 11/27/2014 8:42:23 AM GMT your computer crashed
crash dump file: C:\WINDOWS\memory.dmp
This was probably caused by the following module: wrkrn.sys (WRkrn+0x10C82)
Bugcheck code: 0x50 (0xFFFFFFFFF99814D6, 0x0, 0xFFFFFFFFBF968F6D, 0x0)
Error: PAGE_FAULT_IN_NONPAGED_AREA
file path: C:\WINDOWS\system32\drivers\wrkrn.sys
product: Webroot SecureAnywhere
company: Webroot
description: Webroot SecureAnywhere
Bug check description: This indicates that invalid system memory has been referenced.
This appears to be a typical software driver bug and is not likely to be caused by a hardware problem.
A third party driver was identified as the probable root cause of this system error. It is suggested you look for an update for the following driver: wrkrn.sys (Webroot SecureAnywhere, Webroot).
Google query: Webroot PAGE_FAULT_IN_NONPAGED_AREA
[ boot into Safe Mode WITHOUT Networking, navigate to the location of the file (this is usually C:\Windows\System32\drivers\WRkrn.sys) and RENAME it to something like WRkrnOLD.sys (always better than a straight delete),
*******************************************************************************
* *
* Bugcheck Analysis *
* *
*******************************************************************************
Use !analyze -v to get detailed debugging information.
BugCheck 50, {f99814d6, 0, bf968f6d, 0}
Could not read faulting driver name
*** WARNING: Unable to verify timestamp for WRkrn.sys
*** ERROR: Module load completed but symbols could not be loaded for WRkrn.sys
Probably caused by : WRkrn.sys ( WRkrn+10c82 )
Followup: MachineOwner
To be honest I don't think it will add much more to what we know already and besides without a current install disk there is only so much we can do.This time I also got a big MEMORY.DMP file, It's 232 MB, and I/m not able to upload it here. Know any way around that?
Windows does carry it's own set of drivers. These kick in when you first install the system or when you remove a driver you've installed as an update. Usually it's safe to remove drivers you've installed as long as they are not the ones that came with the os originally.I also today found and installed a nifty NIrSoft program DriverView. It is much of what I was looking for in a drivers info program (as opposed to a drivers update program). I would like a program that goes a step farther and evaluates whether one may safely delete the driver. Do you know of one? Or a website would serve the same purpose.